Selasa, 29 Desember 2009
Jumat, 25 Desember 2009
RESET CANON MP145, MP160
CARA MERESET WASTE INK COUNTER CANON MP160/MP145
Sebelum mereset lihat dulu pesan error yang terdapat pada lcd printer anda :
cara dibawah ini digunakan untuk memperbaiki printer yang mempunyai pesan ERROR E27
1. Matikan printer(pastikan kabel power masih terpasang), tekan dan tahan tombol STOP/RESET kemudian tekan dan tahan tombol ON/OFF dan lepas STOP/RESET,
kemudian tekan tombol STOP/RESET 2x
2. Lepaskan kedua tombol, sekarang printer dalam posisi SERVICE MODE (pada LCD printer muncul angka"0")
3. Setelah lampu on/off berwarna hijau, silahkan tekan tombol STOP/RESET sesuai dengan petunjuk berikut:
di tekan 1x = lampu Orange nyala >untuk Service pattern print
di tekan 2x = lampu Hijau nyala >untuk EEPROM print
di tekan 3x = lampu Orange nyala >untuk EEPROM reset
di tekan 4x = Lampu Hijau Nyala >untuk Waste ink counter reset
4. Matikan printer dan cabut kabel POWER.
5. Hidupkan kembali printer anda
PESAN ERROR
E2-2 = tidak ada kertas (ASF)
E3-3 = Paper jam
E4 = tidak ada tinta/cartridge
E5-5 = ink cartridges tidak terpasang atau cartirdge yang terpasang salah (tidak compatibel)
E8 = absorber full, atau platen waste ink absorber full mita direset
E9 = hubungan ke digital camera / video camera tidak support
E14 = Ink cartridges whose destination are wrong
E15 = Ink cartridge tidak terpasang E16 - Ink remaining is unknown
E16 -E19 = masalah pada scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error (bagian pompa cleaning head)
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = ink absorber full or platen waste ink absorber full > reset dengan toolsnya
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = motor driver tidak normal
E40 20 = hardware lain error
E42 22 = Scanner error
Kamis, 24 Desember 2009
HP LaserJets - Cold Reset Instructions
Cold resetting a printer resets the printer to factory defaults. Please note: Any settings you make at the printers control panel will be reset to factory defaults, including the IP address if you have a JetDirect card installed. Remove the JetDirect card while you cold reset the printer if you don't want to erase the JetDirect card's settings.
You can also reset the NVRAM. Resetting the NVRAM will clear the page count and reset the service mode settings to factory defaults. On printers with a display panel you need to enter service mode to manually change the information stored in NVRAM. On printers that don't have a display panel, such as a 5P, 6P, 2100, 2200 there is a different procedure outlined below.
"Older" printers with a display panel. (e.g. 4000, 4100, 5si, 8000, etc.)
Cold resetting the printer is simply a matter of turning the power off, holding down the GO or Online button while turning the printer on.
Resetting NVRAM settings must be done manually through service mode. See entering service mode.
"Newer" printers with a display panel. (e.g. 2300, 2400, 4200, 4250/4350, 4300, etc.)
Turn the printer off and then on. When the printer begins its memory count, press and hold down the Checkmark button until all the main LED signal lights illuminate and stay illuminated. Then release the Checkmark button, and use the Up/Down arrow keys to find the Cold Reset option, then press the Checkmark button again to choose that option.
Printers with no display panel.
HP 1100, 1200 - While the printer is on, press and hold the Go button for 5 seconds. This will reset the printer.
To reset the NVRAM. Turn the printer off. Press and hold the Go button for 20 seconds while powering on the printer.
HP 2100 - To perform a cold reset, turn the printer power off, then press and hold the JOB CANCEL button. Turn the printer power back on and after all the LEDs come on release the JOB CANCEL button. A cold reset changes most system parameters in NVRAM to the factory defaults. The JOB CANCEL button must be released within 20 seconds after all of the LEDs come on; otherwise, an NVRAM initialization is performed instead of a cold reset.
HP 2200 -
Cold reset:
1. Turn the printer power off.
2. Press and hold GO.
3. Turn the printer power back on and continue to hold GO until the Attention light turns on.
4. Release GO.
5. The device lights will begin cycling from front to rear. The cold-reset process will run until completion and the device will go to the ready state.
NVRAM Reset:
1. Turn the printer power off.
2. Press and hold GO.
3. Turn the printer power back on and continue to hold GO until the Attention, Ready, and Go lights turn on.
4. Release GO.
5. The device lights will begin cycling from font to rear. The NVRAM initialization will run until completion and the device will go to the ready state.
HP 5P & 6P
Cold reset:
Turn the power off and hold the reset button (button closest to the back of the printer) for LESS than 20 seconds while turning the printer on.
Reset the NVRAM:
Turn the power off and hold the reset button for MORE than 20 seconds while turning the printer on..
Rabu, 23 Desember 2009
Cara Reset Printer HP
Permasalahan : Printer HP kebanyakan punya penyakit blink setelah diganti-ganti cartridge. Jadi pada suatu saat printer tidak akan bisa diganti cartridge walaupun dengan yang baru. Masalah blink ini sudah banyak terjadi pada HP.Cara mereset printer:
1. Masukan catridge yang dianggap bagus (printer masih kondisi blink)
2. Matikan printer
3. Tekan dan tahan tombol power sampai head bergerak lalu lepas
4. Apabila catridge bagus blink langsung hilang. Printer sudah dpt digunakan.
Cara reset cartridge HP :
1. Pertama tutup dengan selotip titik2 pada catridge yang berwarna Biru. (berapa titik yang ditutup tergantung type catridge)
2. Buka tutup printer lalu masukan catridge pada printer. Tutup kembali
3. Biasanya printer langsung tidak blink
4. Buka kembali catridge dan cabut selotip yang menempel
5. Tutup titik2 yang berwarna Hijau dengan selotip
6. Buka tutup printer lalu masukan catridge pada printer. Tutup kembali
7. Buka kembali catridge dan cabut selotip yang menempel
8. Catridge sudah bisa digunakan.
Sabtu, 05 Desember 2009
Tampilan Desktop ala Windows 7 pada XP/Vista
Untuk pengguna XP dan Vista yang ingin sekedar merasakan tampilan desktop dan beberapa fitur dasar ala Windows 7 bisa mencoba untuk menggunakan Windows 7 Transformation Pack. Seperti halnya Transformation Pack lainnya, paket ini juga membungkus beberapa tools dan utility kecil serta themes ala Windows 7 kedalam sebuah kemasan siap pakai, namun tentunya tidak sekedar membungkus saja karena semuanya tampak dibikin dengan serius dan bukan asal-asalan.
download
Selasa, 01 Desember 2009
Resetting Epson T10-, Epson T11 and Epson Tx200
Resetting Epson T10-, Epson T11 and Epson Tx200 – Correction
1.Turn off the printer, then move the cartridge carrier to the right side of the printer, and then take out the original cartridges.
2.Use the screwdriver to remove the cover of the cartridge carrier. beware of when opening this cartridge cover.3.Push the cartridge carrier to the right side.
4.Slide the cartridge under the bar, and take out the cartridges from right side.
5.Move the cartridge carrier back to the middle position of compartment, in order to install the cartridges.
6.Install the cartridge in their corresponding color position.
7.Place the T shape adhesive pad on the middle position of compartment.
8.Place the square adhesive pad on the left position of the printer.
9.Attach the tubing between the T shape adhesive pad and square adhesive pad.
10.Place adjust the tubing line, make sure the tubes are not twisted and are straight, with enough room to move back and forth freely with the cartridge compartment movement line.
11.The installation is completed.
We are not responsible for damaged, all you do is you own risk because we never tried it before. Let us know if this procedure worked.
resseter epson T-10, T-11 :download
ressetter epson TX200 :download
iP1200,RESET PRINTER CANON SERI : iP1300, iP1600, iP1700, iP1800, iP2200, dan iP2500
iP Tool versi 0.9.2 adalah software resetter untuk printer Canon type iPxxxx. Adapun type yang dapat direset oleh sofware ini adalah :
iP1200, iP1300, iP1600, iP1700, iP1800, iP2200, dan iP2500
Berbeda dengan sofware resetter lainnya, sofware ini penggunaan sangat mudah.
download
Subscribe to:
Postingan (Atom)
